TENİ FOCUS ANAHTAR PROGRAMLAMA

Question

Aracımın uzaktan kumandalı anahtarına su girmiş ve programı şaştı. Şu an;
1- Bagaj kapısının açılma butonuna bastığımda tüm kapılar açılıyor.
2-Kapıları kapama veya Kapıları açma butonuna bastığımda hiç bir işlem yapılmıyor.
3- Bagaj kapısı açma ve kapı açma butonlarına birlikte bastığımda tüm kapılar açılıyor.

Ben ise tüm butonların normal görevini yapmasını istiyorum.
Servise gittim anahtarın değişmesi gerekir dediler ben buna inanmıyorum.Bu sorunun programın yenilenmesi ile çözüleceğini düşünüyorum.
Bilgi sahibi arkadaşlar acil yardım lütfen!!!!!!!!!!!

Answer

Key Operation and Programming
Remote alarm/central locking
System operation
Alarm/central locking functions can be altered using diagnostic equipment.
Pressing lock button twice within 2 seconds activates double locking system.
Some models:
Holding key lock button in depressed position closes windows and sunroof.
Pressing key unlock button once deactivates system and unlocks driver's door only.
Pressing key unlock button twice within 3 seconds deactivates system and unlocks all doors.
Switch ignition ON.
Ensure clock LED illuminates for 3 seconds.
If LED flashes rapidly at regular intervals for approximately 1 minute, then flashes at irregular intervals:
Key code not recognised.
Remove key and try again.
Programming
When
Key(s) added or replaced.
System malfunction.
How
Obtain all keys fitted with remote control.
Fasten seat belts and close all doors.
Turn ignition switch from position I to position II 4 times within 6 seconds.
Turn ignition switch to position I (¨11/2000).
Switch ignition OFF (12/2000¨).
Programming mode activated for 10 seconds proceed as follows:
Press and hold lock, unlock or boot release button Fig. 01 [1], [2] or [3].
Wait for acoustic signal (indicates correct programming).
Repeat above procedure within 10 seconds to program remaining keys.
To exit programming mode:
Turn ignition switch to position III or wait 10 seconds.
Keys can also be programmed using diagnostic equipment.

NOTE: A maximum of 4 keys can be programmed.

Battery replacement
Immobilizer
System operation
System arms 5 seconds after switching ignition OFF.
Switch ignition ON.
Ensure clock LED illuminates for 3-5 seconds.
If LED flashes rapidly at regular intervals for approximately 1 minute, then flashes at irregular intervals:
Key code not recognised.
Remove key and try again.
Programming
When
System malfunction: LED illuminates for 1 minute, then flashes at irregular intervals.
Key(s) added or replaced.

NOTE: Replacement keys MUST have blue mark. Keys with red mark are NOT compatible with this system.

How
NOTE: Programming method using vehicle keys can be deactivated using diagnostic equipment.

Obtain 2 programmed keys (A and B).
Insert key A into ignition switch.
Turn ignition switch to position II. Wait 1 second.
Switch ignition OFF. Remove key A.
Insert key B into ignition switch within 5 seconds.
Turn ignition switch to position II. Wait 1 second.
Switch ignition OFF. Remove key B.
Within 10 seconds:
Insert key to be programmed into ignition switch.
Turn ignition switch to position II. Wait 4 seconds.
Switch ignition OFF. Wait 5 seconds.
Start engine.
If engine does not start and clock LED flashes:
Switch ignition ON. Wait at least 20 seconds.
Switch ignition OFF. Repeat programming procedure.
Repeat above procedure to program remaining keys.
Keys can also be programmed using diagnostic equipment.

NOTE: A maximum of 8 keys can be programmed, including a maximum of 4 with remote control.

Answer

Teşekkür ederim ama bu yazıyı ingilizce öğretmen,i arkadaşım bile çevirmekte zorlandı Türkçesi varsa çok daha fazla işime yarayacak Hakan Usta İlginiz için tekrar teşekkürler

Answer

MERHABA,  aracımın anahtarının pilini değiştiricem nasıl açıldığı konusunda yARDIMCI OLURMUSUNUZ

TENİ FOCUS ANAHTAR PROGRAMLAMA

Benzer içerikler